Diagonal compression of hollow concrete block masonry, as an indicator of structural vulnerability.
Abstract
The objective of this work was to evaluate the performance of artisanal and semi-industrial blocks, used to make prisms and walls, under vertical and diagonal stresses necessary to determine the structural vulnerability of buildings to seismic hazards. Concrete block masonry constructions are commonly used in the Pacific region of Nicaragua, mainly in housing projects. In 2017, the Ministry of Transportation and Infrastructure, published the "Minimum Standard for Design and Construction of Masonry MP-001", as a complement to the National Construction Regulations. However, this standard does not take into account the characteristics and properties of local materials. Concrete blocks prisms and walls were elaborated, and failure types and mechanical performance at later ages were determined. The results showed a tendency to diagonal stress failures in walls, with an average strength (Vm) of 6.7 kg/cm2, higher than those reported in the literature.
Downloads
References
Aguilar Arriola, E. J. (2016). “Importancia de La Vulnerabilidad Estructural de La Vivienda Unifamiliar En El Riesgo Urbano. Modelo de Estudio Ciudad de Managua, Nicaragua.” Revista de Urbanismo 0(35). https://revistaurbanismo.uchile.cl/index.php/RU/article/view/43090 DOI: https://doi.org/10.5354/0717-5051.2016.43090
Argento, R. S., Ferreyra, J., Murdoch Anderson, A, Carrasco, M. F., González, A., Grether, R. M. (2019). “Residuos de Desmote de Algodón Aglomerados: Su Producción y Aplicación En La Construcción de Viviendas.” Ambiente Construído 19(3):127–45. https://doi.org/10.1590/s1678-86212019000300329
American Society for Testing and Materials (2000). Annual Book of ASTM Standards, Section Four, Construction, Volume 04.2 Construction, Concrete and Aggregates. USA: ASTM.
Bonett Díaz, R. L. (2003). “Vulnerabilidad y Riesgo Sísmico de Edificios, Aplicación a Entornos Urbanos En Zonas de Amenaza Alta y Moderada.” Universidad Politécnica de Cataluña.
Fernández Baqueiro, L., Marín Gómez, F., Varela Rivera, J. y Vargas Marín, G. (2009). Determinación de la resistencia a compresión diagonal y el módulo de cortante de la mampostería de bloques huecos de concreto. Ingeniería, Revista Académica de la FI-UADY, 13-2, pp. 41-50, ISSN: 1665-529X.
Freeda Christy, C., Tensing, D., Mercy Shanthi, R. (2013). “Experimental Study on Axial Compressive Strength and Elastic Modulus of the Clay and Fly Ash Brick Masonry.” Journal of Civil Engineering and Construction Technology, 4(4):134–41. https://academicjournals-org.webpkgcache.com/doc/-/s/academicjournals.org/article/article1379608865_Freeda%20et%20al.pdf
Hernández, E. (2017). Construcción durable - Una visión de futuro para Nicaragua. Revista Arquitectura +, 2(4), 8–12. https://doi.org/10.5377/arquitectura.v2i4.9139
MTI. 2007. “Reglamento Nacional de Contrucción.” 156.
MTI. 2017. “Norma Mínima de Diseño y Construcción de Mampostería (MP-001).” Ministerio de Transporte e Infraestructura 1–58.
Organismo Nacional de Normalización y Certificación de la Construcción y Edificación, S.C. (2011). NMX-C-464-ONNCCE-2010 - Industria de la Construcción-Mampostería-Determinación de la resistencia a compresión diagonal y módulo de cortante de muretes, asi como determinación de la resistencia a compresión y módulo de elasticidad de pilas de mampostería de arcilla o de concreto. Comité técnico de normalización de productos, sistemas y servicios para la construcción.
NTON 12 008. 2016. “Materiales de Construcción. Bloque Hueco y Sólido a Base de Cemento y Agregados Pétreos. Requisitos y Evaluación de La Conformidad.”
Pujol, S., Rodriguez, M. E. (2019). Evaluación del comportamiento de muros no estructurales en edificios de la ciudad de México en el terremoto del 19 de septiembre 2017. Revista Ingeniería Sísmica, (101), 53–66. https://doi.org/10.18867/ris.101.529
Ruíz Valverde, H. Y., Morales Leiva, F. (2018). “Vulnerabilidad estructural en viviendas de interés social hechas con bloques de concreto en managua.” Universidad Nacional de Ingeniería.
Sánchez Tizapa, S., Villaseñor Franco, A., Guinto Herrera, E., Barragán Trinidad, R., Mebarki, A. (2017). Propuesta de valores de referencia para la resistencia de diseño a compresión diagonal y compresión de la mampostería en el estado de Guerrero, México. Revista ALCONPAT, 7(3), 231 - 246. https://doi.org/10.21041/ra.v7i3.159 DOI: https://doi.org/10.21041/ra.v7i3.159
Tena, A., Liga, A., Pérez, A., González, F. (2017). Propuesta de mejora de mezclas para producir piezas de mampostería de concreto empleando materiales comúnmente disponibles en el Valle de México. Revista ALCONPAT, 7(1), 36-56. https://doi.org/10.21041/ra.v7i1.170 DOI: https://doi.org/10.21041/ra.v7i1.170
Tena Colunga, A., Juárez Ángeles, A., Salinas Vallejo, V. H. (2007). Resistencia y deformación de muros de mampostería combinada y confinada sujetos a cargas laterales. Revista Ingeniería Sísmica, (76), 29–60. https://doi.org/10.18867/ris.76.58 DOI: https://doi.org/10.18867/ris.76.58
Copyright (c) 2025 Hernández, E. F., Aguilar Arriola, E. J., Martínez, H.

This work is licensed under a Creative Commons Attribution 4.0 International License.
_______________________________
License in effect from September 2020
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.